Watson-marlow APEX10 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Čerpadla Watson-marlow APEX10. Watson-Marlow APEX10 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 72
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
1
Disc
The disc inserted in the front cover contains the user manual of the models APEX10,
APEX15 and APEX20. The user manual is available in the following languages:
The disc also contains quick-reference instructions for the replacement of the pump
hose. This replacement instruction is only for users that are familiar with the
replacement procedures in the user manual.
How to use the disc
1 Put the disc in the disc drive.
2 Close the disc drive.
The disc will start automatically.
3 Wait until the various language versions appear on screen.
4 Select the required language (click 1x with the left mouse button).
The PDF reader program will automatically start and the required user manual
appears on screen.
Shortcuts
In the left margin you will find the various chapters and paragraphs. These can be
accessed directly by clicking on the required chapter or paragraph.
In the text you will find hyperlinks to chapters or paragraphs. These hyperlinks are linked
with the required chapters or paragraphs. By clicking a shortcut the required chapter or
paragraph appears on screen.
System requirements
The program on the disc requires a PC with the following minimum system
requirements:
CD drive
The following software must be installed on the PC:
PDF reader program
an internet browser
Zobrazit stránku 0
1 2 3 4 5 6 ... 71 72

Shrnutí obsahu

Strany 1 - • an internet browser

1DiscThe disc inserted in the front cover contains the user manual of the models APEX10,APEX15 and APEX20. The user manual is available in the followi

Strany 2

SAFETY102SAFETY2.1 SymbolsIn this manual the following symbols are used:2.2 Intended useThe hose pump is exclusively designed for pumpingsuitable prod

Strany 3 - APEX10, APEX15 and APEX20

SAFETY11is not in conformance with the intended use. If you wantto change the application of your hose pump, contactyour Bredel representative first.2

Strany 4

SAFETY122.5 ResponsibilityThe manufacturer does not accept any responsibility fordamage or harm caused by not observing the safetyregulations and inst

Strany 5

WARRANTY CONDITIONS133 WARRANTY CONDITIONSThe manufacturer offers a two-year warranty on allparts of the hose pump. This means that all parts will ber

Strany 6

DESCRIPTION144 DESCRIPTION4.1 Identification of the product4.1.1 Identification of the productThe hose pump can be identified by identification plates

Strany 7

DESCRIPTION154.1.4 Identification of the electric motorThe identification plate on the electric motor containsthe following data:B Serial numberC Arti

Strany 8

DESCRIPTION164.2 Construction of the pumpA CoverB RotorC Pump hoseD Pump housingE SupportF GearboxG Electric motorH Frequency controllerDCEGBFAH

Strany 9

DESCRIPTION174.3 Operation of the pumpThe heart of the pumphead consists of a speciallyconstructed pump hose (A) which lies against the insideof the p

Strany 10

DESCRIPTION184.4 Pump hose4.4.1 GeneralA Extruded outer layer made of natural rubberB Two nylon reinforcement layersC Extruded inner linerThe pump hos

Strany 11

DESCRIPTION194.4.2 Hose compression force adjustmentThe compression force on the pump hose can beadjusted by installing a rotor with a different dimen

Strany 13

DESCRIPTION204.5 GearboxThe hose pump types described in this manual usehelical gearbox units. Other gearbox types are availableas option. The gearbox

Strany 14 - 10 15 20

INSTALLATION215INSTALLATION5.1 UnpackingFollow the unpacking instructions on the packaging oron the hose pump, the gearbox and the electric motor.5.2

Strany 15 - Bredel article number E384083

INSTALLATION225.3.3 PipeworkWhen determining and connecting suction anddischarge lines consider the following points:• It is recommended that the bore

Strany 16

INSTALLATION235.3.4 MotorThe motor connection must meet the local applicableregulations. A thermal safety device should reduce therisk of a motor over

Strany 17

INSTALLATION24• All control cables outside the enclosure must beshielded and have a cross sectional areabetween 0.22 mm2 and 1 mm2. The shieldingmust

Strany 18

COMMISSIONING256 COMMISSIONING6.1 Preparations1. Connect the electric motor and, if present, thefrequency controller in conformance with thelocally ap

Strany 19

COMMISSIONING266.2 Commissioning1. Connect the pipework.2. Make sure that there are no obstructions suchas closed valves.3. Switch on the hose pump.4.

Strany 20

OPERATION277 OPERATION7.1 TemperatureThe pump will heat up during normal operation. Heat isgenerated in the contact zone between the pressingshoe and

Strany 21

OPERATION287.3 Performance graphsUseful operating duties can be found in theperformance graphs in which discharge-pressurecurves are displayed in a sp

Strany 22

OPERATION297.3.1 Performance graph APEX10:7.3.2 Performance graph APEX15:0.0002040405060708060 80 100 120 1400 55 110 165 220 275 330 3850.050.100.150

Strany 23

3Hose pump series APEX10, APEX15 and APEX20ManualTYPE EL - CLASS IAUGUST 2012EnvironmentalManagementISO14001QualityManagementISO 9001

Strany 24

OPERATION307.3.3 Performance graph APEX20:7.4 Dry runningDry running is a running condition of the pump when nofluid is flowing through the pump. Bred

Strany 25

OPERATION317.5 Hose failureCause of a hose failureThe hose in a peristaltic pump has to withstand manyload cycles of considerable magnitude. The repet

Strany 26

OPERATION32• Hazardous situations• Additional downtimeHose failure will result in additional downtime,because you must clean the pump before a newhose

Strany 27

OPERATION337.6 Fluid leakageThe APEX pump uses a lubricated rotor to compressthe hose. This means the pumphead must be filled withsufficient lubricant

Strany 28

MAINTENANCE348 MAINTENANCE8.1 GeneralOnly use original Bredel parts when maintaining thehose pump. Bredel cannot guarantee correct operationand any co

Strany 29 - OPERATION

MAINTENANCE35Point Action To be carried out Remark1 Checking the lubricant level.Before starting the pump and at scheduled inter-vals during operation

Strany 30

MAINTENANCE368.3 Cleaning the pump hoseThe inside of the pump hose can be easily cleaned byrinsing the pump with clean water. If a cleaning fluid isad

Strany 31

MAINTENANCE373. Keep on pouring until the lubricant level hasrisen above the level line in the inspectionwindow. Place back the breather cap.8.5 Repla

Strany 32 - • Large spill of product

MAINTENANCE386. Loosen the bolts (A) of the bracket (B) andremove the bolts.7. Pull the bracket and hose clamp from the hose.Then pull off the rubber

Strany 33

MAINTENANCE395. Check the rotor for wear or damage and replacethe rotor if necessary. Also refer to themaintenance diagram in § 8.2.6. Place back the

Strany 34

4© 2014 Watson-Marlow Bredel B.V.All rights reserved.The information provided herein may not be reproduced and/or published in any form,by print, phot

Strany 35

MAINTENANCE404. Check that the rubber bushes (A) are notdeformed or damaged and replace them ifnecessary.5. Check that the hose clamps (B) are notdama

Strany 36

MAINTENANCE418.6 Exchanging replacement parts8.6.1 Replacing rotor, bearings and seal ring1. Remove the pump hose. Refer to § 8.5.1.2. Isolate the pum

Strany 37

MAINTENANCE427. Put a plastic or wooden drive pin (A) on therotor.8. Hit the drive pin firmly with a hammer to removethe rotor.9. Put the hose pump up

Strany 38

MAINTENANCE4313. Fit a new seal ring (A) using good engineeringpractices. The seal ring must be fitted in thecorrect orientation (B). Make sure that t

Strany 39

MAINTENANCE4417. Put the hose pump on two blocks, on its side asshown.18. Fit the pump drive (A) with the nuts (B) andwashers (C). Make sure the coupl

Strany 40

MAINTENANCE452. Mount the breather (A) with high-level floatswitch.3. Connect the high-level float switch to theauxiliary power circuit via the 1.5 me

Strany 41

MAINTENANCE468.7.2 Replacing the revolution counter1. Jog the rotor until the pressing shoe is clearlyvisible through the inspection window. Now thepr

Strany 42

MAINTENANCE477. Tighten the nuts so that the distance betweenthe sensor and the rotor (X) is between 0.75mm and 1.25 mm.8. Check if the revolution cou

Strany 43

STORAGE489STORAGE9.1 Hose pump• Store the hose pump and pump parts in a dryarea. Make sure that the hose pump and pumpparts are not exposed to tempera

Strany 44

TROUBLESHOOTING4910 TROUBLESHOOTINGIf the hose pump does not function (correctly), consult the following checklist to see ifyou can remedy the error y

Strany 45

5CONTENTS1GENERAL1.1 How to use this manual ... 81.2 Original instructions ..

Strany 46

TROUBLESHOOTING50High pump temperature. Non-standard hose lubri-cant used.Consult your Bredel repre-sentative for the correct lubricant.Low lubricant

Strany 47

TROUBLESHOOTING51Low capacity / pressure. Shut-off valve in the suc-tion line (partly) closed.Fully open the shut-off valve.Hose rupture or badly worn

Strany 48

TROUBLESHOOTING52Vibration of the pump and pipework.Suction and discharge lines are not secured cor-rectly.Check and secure pipe-work. High pump speed

Strany 49

TROUBLESHOOTING53Hose pulled into the pump.Insufficient or no hose lubricant in the pumphead.Add extra lubricant. Refer to § 8.4.Incorrect lubricant:

Strany 50

SPECIFICATIONS5411 SPECIFICATIONS11.1 Pumphead11.1.1 PerformanceDescription APEX10 APEX15 APEX20∅ 10 mm ∅ 15 mm ∅ 20 mmMax. capacity, continuous [m3/h

Strany 51

SPECIFICATIONS5511.1.2 MaterialsPos Description Material1 Pump housing Aluminium2 Cover Aluminium3 Cover window PMMA4 Pump rotor Cast-iron5 Pump suppo

Strany 52

SPECIFICATIONS5611.1.3 Surface treatment• After surface preparation, one layer of two-component acrylate is used forsurface protection. Standard colou

Strany 53

SPECIFICATIONS5711.1.5 WeightsDescription Weight [kg]Pumphead (inclusive of hose, lubricant and pump support) 17.6Pump support 2.4Rotor 4.8 ... 5.6Hos

Strany 54 - 11.1.1 Performance

SPECIFICATIONS5811.1.6 Torque figuresPos Description Bolt size** All steel bolts are class 8.8.Torque [Nm]1Cover M6x25 102 Hose clamp**** Due to creep

Strany 55 - 11.1.2 Materials

SPECIFICATIONS5911.2 Gearbox11.3 Electric motorStandard electric motor design is an enclosed three-phase asynchronous motor. Athermal safety device to

Strany 56

65 INSTALLATION5.1 Unpacking ... 215.2 Inspection ...

Strany 57 - 11.1.5 Weights

SPECIFICATIONS6011.4 Variable Frequency Drive (VFD) (optional)The Bredel Variable Frequency Drive (VFD) has been preprogrammed and only needsto be con

Strany 58 - 11.1.6 Torque figures

SPECIFICATIONS6111.5.2 OverviewPos. Description1 Cover assembly. Refer to § 11.5.3.2 Pumphead assembly. Refer to § 11.5.4.3 Pump support assembly. Ref

Strany 59

SPECIFICATIONS6211.5.3 Cover assemblyPos. Qty. Description1 8 Cover screw2 8 Cover screw washer3 1 Drain plug O-ring4 1 Drain plug5 1 Breather screw61

Strany 60

SPECIFICATIONS6311.5.4 Pumphead assemblyPos. Qty. Description10 1 Hose NR1Hose NBR1Hose F-NBR1Hose EPDM1Hose CSM11 1 Pump housing12 1 Rotor, low-press

Strany 61 - 11.5.2 Overview

SPECIFICATIONS6411.5.5 Support assemblyPos. Qty. Description20 1 Pump support21 4 Support nut22 4 Support nut washer23 1 Orientation screw20212223

Strany 62 - 11.5.3 Cover assembly

SPECIFICATIONS6511.5.6 Barbed nipple assembly (PTFE/PDVF)All parts differ for the APEX10, APEX15 and APEX20 except for the bracket bolt and the bracke

Strany 63 - 11.5.4 Pumphead assembly

SPECIFICATIONS6611.5.7 Barbed or threaded nipple assembly (stainless steel/PP/PVC)All parts differ for the APEX10, APEX15 and APEX20 except for the br

Strany 64 - 11.5.5 Support assembly

SPECIFICATIONS6711.5.8 Flange assembly with insert with collarAll parts differ for the APEX10, APEX15 and APEX20 except for the bracket bolt and the b

Strany 65

SPECIFICATIONS6811.5.9 Flange assembly with threaded nipple11.5.10 LubricantAll parts differ for the APEX10, APEX15 and APEX20 except for the bracket

Strany 66 - EHEDG compliant

ORIGINAL69Translation of original certificateEC DECLARATION OF CONFORMITY OF THE MACHINERY(according to Annex II.1.A. of Directive 2006/42/EC on machi

Strany 67

79 STORAGE9.1 Hose pump ... 489.2 Pump hose ...

Strany 68

SAFETY FORMSafety formSAFETY FORMProduct Use and Decontamination DeclarationIn compliance with the Health and Safety Regulations, the user is required

Strany 69

NOTES71NotesNOTES

Strany 70 - SAFETY FORM

7229210320 TS11-003-BWatson-Marlow Bredel B.V.P.O. Box 47NL-7490 AA DeldenThe NetherlandsTelephone: +31 (0)74 3770000Fax: +31 (0)74 3761175E-mail: bre

Strany 71

GENERAL81GENERAL1.1 How to use this manualThis manual is intended as a reference book by meansof which qualified users are able to install, commission

Strany 72 - Management

GENERAL91.5 Environment and disposal of wasteEnquire within your local government about thepossibilities for reuse or environment-friendlyprocessing o

Příbuzné modely APEX15 | APEX20 | APEX28 | APEX35 |

Komentáře k této Příručce

Žádné komentáře